A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
The content below about How to Install a Bathtub is seriously enjoyable. You should keep reading.
Mounting a tub isn't specifically rocket science, yet it does call for strong plumbing, carpentry, and also often, tiling skills. Replacing an old bathtub with a brand-new one is additionally a reasonably difficult project. If the old tub is conveniently obtainable, the task can relocate immediately; if you need to open a wall to get rid of the old tub as well as place the new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Make certain you have actually certified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is better to consider employing one prior to you start. Possibilities are you may require an expert plumber to make tube links.
This write-up will certainly assist you install a new bath tub in your shower room if you have already bought a brand-new tub and don't require to alter the arrangement of your previous water pipes.
Your tools as well as material list ought to comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing compound.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area between the tap and also the sink. Protect the tap in position with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous kind ought to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Tub
Making use of both wooden boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The next goal is to make certain that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bathtub till the level checks out level.
To mount faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water supply as well as check all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub as well as additionally check the overflow electrical outlet and also the typical outlet for leakages.
Ultimately, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub should wait till the bathtub has been made use of a minimum of when as this will resolve it into its last position.
Getting ready for the Installation
To start with, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is important to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable tap ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be fitted in its final position.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, causing the water to pass through the wall in between the bath and the tiling, causing issues with moisture and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to always fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack rather very early if you do not take into account this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Give feedback down the page. We would be glad to find out your suggestions about this post. In hopes that you come back again soon. Do you know somebody who is in the market for the subject? Please feel free to promote it. Bless you for your time. Visit again soon.
Real results? Dial! Report this page